User Manual ########### This manual is an early work in progress, not least because Liminix is not yet really ready for users who are not also developers. Your feedback to improve it is very welcome. Installation ************ The Liminix installation process is not quite like installing NixOS on a real computer, but some NixOS experience will nevertheless be helpful in understanding it. The steps are as follows: * Decide whether you want the device to be updatable in-place (there are advantages and disadvantages), or if you are happy to generate and flash a new image whenever changes are required. * Create a :file:`configuration.nix` describing the system you want * Build an image * Flash it to the device Supported devices ================= For a list of devices that Liminix (present or previous versions) has run on, refer to `devices/ in the source repo `_. For devices that _currently_ build, cross-reference it with `the CI status `_. Everything that builds is (usually) expected to run, so if you end up with an image that builds but doesn't boot, please report it as a bug. As of June 2023 the device list is a little thin. Adding devices based on the Atheros or Mediatek (Ralink) platform should be quite straightforward if you have some C/Linux kernel experience and are prepared to open it up and attach serial wires: please refer to the Developer Manual. Choosing a flavour (read-only or updatable) =========================================== Liminix installations come in two "flavours"- read-only or in-place updatable: * a read-only installation can't be updated once it is flashed to your device, and so must be reinstalled in its entirety every time you want to change it. It uses the ``squashfs`` filesystem which has very good compression ratios and so you can pack quite a lot of useful stuff onto your device. This is good if you don't expect to change it often. * an updatable installation has a writable filesystem so that you can update configuration, upgrade packages and install new packages over the network after installation. This uses the `jffs2 `_ filesystem: although it does compress the data, the need to support writes means that it can't pack quite as small as squashfs, so you will not have as much space to play with. Updatability caveats ~~~~~~~~~~~~~~~~~~~~ At the time of writing this manual the read-only squashfs support is much more mature. Consider also that it may not be possible to perform "larger" updates in-place even if you do opt for updatability. If you have (for example) an 11MB system on a 16MB device, you won't be able to do an in-place update of something fundamental like the C library (libc), as this will temporarily require 22MB to install all the packages needing the new library before the packages using the old library can be removed. A writable system will be more useful for smaller updates such as installing a new package (perhaps you temporarily need tcpdump to diagnose a network problem) or for changing configuration files. Note also that the kernel is not part of the filesystem so cannot be updated this way. Kernel changes require a full reflash. Creating configuration.nix ========================== You need to create a :file:`configuration.nix` that describes your device and the services that you want to run on it. Start by copying :file:`vanilla-configuration.nix` and adjusting it, or look in the `examples` directory for some pre-written configurations. :file:`configuration.nix` conventionally describes the packages, services, user accounts etc of the device. It does not describe the hardware itself, which is specified separately in the build command (as you will see below). Your configuration may include modules: it probably *should* include the ``standard`` module unless you understand what it does and what happens if you leave it out. .. code-block:: nix imports = [ ./modules/standard.nix ] configuration.rootfsType = "jffs2"; # or "squashfs" Building ======== Build Liminix using the :file:`default.nix` in the project toplevel directory, passing it arguments for configuration and hardware. For example: .. code-block:: console nix-build -I liminix-config=./tests/smoke/configuration.nix \ --arg device "import ./devices/qemu" -A outputs.default In this command ```` points to your :file:`configuration.nix`, ``device`` is the file for your hardware device definition, and ``outputs.default`` will generate some kind of Liminix image output appropriate to that device. For the qemu device in this example, ``outputs.default`` is an alias for ``outputs.vmbuild``, which creates a directory containing a squashfs root image and a kernel. You can use the :command:`mips-vm` command to run this. For the currently supported hardware devices, ``outputs.default`` creates a directory containing a file called ``firmware.bin``. This is a raw image file that can be written directly to the firmware flash partition. Flashing ======== Flashing from the boot monitor ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ If you are prepared to open the device and have a TTL serial adaptor of some kind to connect it to, you can probably flash it using U-Boot. This is quite hardware-specific, and sometimes involves soldering: please refer to the Developer Manual. Flashing from an existing Liminix system with :command:`flashcp` ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The flash procedure from an existing Liminix-system is two-step. First we reboot the device (using "kexec") into an "ephemeral" RAM-based version of the new configuration, then when we're happy it works we can flash the image - and if it doesn't work we can reboot the device again and it will boot from the old image. Building the RAM-based image ............................ To create the ephemeral image, build ``outputs.kexecboot`` instead of ``outputs.default``. This generates a directory containing the root filesystem image and kernel, along with an executable called `kexec` and a `boot.sh` script that runs it with appropriate arguments. For example .. code-block:: console nix-build --show-trace -I liminix-config=./examples/arhcive.nix \ --arg device "import ./devices/gl-ar750" -A outputs.kexecboot && \ (tar chf - result | ssh root@the-device tar -C /run -xvf -) and then login to the device and run .. code-block:: console cd /run/result sh ./boot.sh . This will load the new kernel and map the root filesystem into a RAM disk, then start executing the new kernel. *This is effectively a reboot - be sure to close all open files and finish anything else you were doing first.* If the new system crashes or is rebooted, then the device will revert to the old configuration it finds in flash. Building the second (permanent) image ..................................... While running in the kexecboot system, you can copy the permanent image to the device with :command:`ssh` .. code-block:: console build-machine$ tar chf - result/firmware.bin | \ ssh root@the-device tar -C /run -xvf - Next you need to connect to the device and locate the "firmware" partition, which you can do with a combination of :command:`dmesg` output and the contents of :file:`/proc/mtd` .. code-block:: console <5>[ 0.469841] Creating 4 MTD partitions on "spi0.0": <5>[ 0.474837] 0x000000000000-0x000000040000 : "u-boot" <5>[ 0.480796] 0x000000040000-0x000000050000 : "u-boot-env" <5>[ 0.487056] 0x000000050000-0x000000060000 : "art" <5>[ 0.492753] 0x000000060000-0x000001000000 : "firmware" # cat /proc/mtd dev: size erasesize name mtd0: 00040000 00001000 "u-boot" mtd1: 00010000 00001000 "u-boot-env" mtd2: 00010000 00001000 "art" mtd3: 00fa0000 00001000 "firmware" mtd4: 002a0000 00001000 "kernel" mtd5: 00d00000 00001000 "rootfs" Now run (in this example) .. code-block:: console flashcp -v firmware.bin /dev/mtd3 "I know my new image is good, can I skip the intemediate step?" ``````````````````````````````````````````````````````````````` In addition to giving you a chance to see if the new image works, this two-step process ensures that you're not copying the new image over the top of the active root filesystem. It might work, or it might crash in surprising ways. Flashing from OpenWrt (not currently advised!) ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .. CAUTION:: At your own risk! This will (at least in some circumstances) lead to bricking the device: we think this flash method is currently incompatible with use of a writeable (jffs2) filesystem. If your device is running OpenWrt then it probably has the :command:`mtd` command installed. After transferring the image onto the device using e.g. :command:`ssh`, you can run it as follows: .. code-block:: console mtd -r write /tmp/firmware.bin firmware For more information, please see the `OpenWrt manual `_ which may also contain (hardware-dependent) instructions on how to flash an image using the vendor firmware - perhaps even from a web interface. Updating an installed system (JFFS2) ************************************ Adding packages =============== If your device is running a JFFS2 root filesystem, you can build extra packages for it on your build system and copy them to the device: any package in Nixpkgs or in the Liminix overlay is available with the ``pkgs`` prefix: .. code-block:: console nix-build -I liminix-config=./my-configuration.nix \ --arg device "import ./devices/mydevice" -A pkgs.tcpdump nix-shell -p min-copy-closure root@the-device result/ Note that this only copies the package to the device: it doesn't update any profile to add it to ``$PATH`` Rebuilding the system ===================== :command:`liminix-rebuild` is the Liminix analogue of :command:`nixos-rebuild`, although its operation is a bit different because it expects to run on a build machine and then copy to the host device. Run it with the same ``liminix-config`` and ``device`` parameters as you would run :command:`nix-build`, and it will build any new/changed packages and then copy them to the device using SSH. For example: .. code-block:: console liminix-rebuild root@the-device -I liminix-config=./examples/rotuer.nix --arg device "import ./devices/gl-ar750" This will * build anything that needs building * copy new or changed packages to the device * reboot the device It doesn't delete old packages automatically: to do that run :command:`min-collect-garbage`, which will delete any packages not in the current system closure. Note that Liminix does not have the NixOS concept of environments or generations, and there is no way back from this except for building the previous configuration again. Caveats ~~~~~~~ * it needs there to be enough free space on the device for all the new packages in addition to all the packages already on it - which may be a problem if a lot of things have changed (e.g. a new version of nixpkgs). * it cannot upgrade the kernel, only userland Configuration options ********************* .. include:: modules.rst