forked from dan/liminix
235 lines
6.9 KiB
Nix
235 lines
6.9 KiB
Nix
{
|
|
description = ''
|
|
Belkin RT-3200 / Linksys E8450
|
|
******************************
|
|
|
|
This device is based on a 64 bit Mediatek MT7622 ARM platform,
|
|
and is "work in progress" in Liminix.
|
|
|
|
.. note:: The factory flash image contains ECC errors that make it
|
|
incompatible with Liminix: you need to use the `OpenWrt
|
|
UBI Installer <https://github.com/dangowrt/owrt-ubi-installer>`_ to
|
|
rewrite the partition layout before you can flash
|
|
Liminix onto it (or even use it with
|
|
:ref:`system-outputs-tftpboot`, if you want the wireless
|
|
to work).
|
|
|
|
Hardware summary
|
|
================
|
|
|
|
- MediaTek MT7622BV (1350MHz)
|
|
- 128MB NAND flash
|
|
- 512MB RAM
|
|
- b/g/n wireless using MediaTek MT7622BV (MT7615E driver)
|
|
- a/n/ac/ax wireless using MediaTek MT7915E
|
|
|
|
|
|
Installation
|
|
============
|
|
|
|
Installation is currently a manual process (you need a :ref:`serial <serial>` conection and
|
|
TFTP) following the instructions at :ref:`system-outputs-ubimage`
|
|
|
|
'';
|
|
|
|
system = {
|
|
crossSystem = {
|
|
config = "aarch64-unknown-linux-musl";
|
|
};
|
|
};
|
|
|
|
module = {pkgs, config, lib, lim, ... }:
|
|
let firmware = pkgs.stdenv.mkDerivation {
|
|
name = "wlan-firmware";
|
|
phases = ["installPhase"];
|
|
installPhase = ''
|
|
mkdir $out
|
|
cp ${pkgs.linux-firmware}/lib/firmware/mediatek/{mt7915,mt7615,mt7622}* $out
|
|
'';
|
|
};
|
|
in {
|
|
imports = [
|
|
../../modules/arch/aarch64.nix
|
|
../../modules/outputs/tftpboot.nix
|
|
../../modules/outputs/ubifs.nix
|
|
];
|
|
config = {
|
|
kernel = {
|
|
src = pkgs.pkgsBuildBuild.fetchurl {
|
|
name = "linux.tar.gz";
|
|
url = "https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.15.137.tar.gz";
|
|
hash = "sha256-PkdzUKZ0IpBiWe/RS70J76JKnBFzRblWcKlaIFNxnHQ=";
|
|
};
|
|
extraPatchPhase = ''
|
|
${pkgs.openwrt.applyPatches.mediatek}
|
|
'';
|
|
config = {
|
|
PCI = "y";
|
|
ARCH_MEDIATEK = "y";
|
|
# ARM_MEDIATEK_CPUFREQ = "y";
|
|
|
|
# needed for "Cannot find regmap for /infracfg@10000000"
|
|
MFD_SYSCON = "y";
|
|
MTK_INFRACFG = "y";
|
|
|
|
MTK_PMIC_WRAP = "y";
|
|
MTK_EFUSE="y";
|
|
# MTK_HSDMA="y";
|
|
MTK_SCPSYS="y";
|
|
MTK_SCPSYS_PM_DOMAINS="y";
|
|
# MTK_THERMAL="y";
|
|
MTK_TIMER="y";
|
|
|
|
COMMON_CLK_MT7622 = "y";
|
|
COMMON_CLK_MT7622_ETHSYS = "y";
|
|
COMMON_CLK_MT7622_HIFSYS = "y";
|
|
COMMON_CLK_MT7622_AUDSYS = "y";
|
|
PM_CLK="y";
|
|
|
|
REGMAP_MMIO = "y";
|
|
CLKSRC_MMIO = "y";
|
|
REGMAP = "y";
|
|
|
|
MEDIATEK_GE_PHY = "y";
|
|
# MEDIATEK_MT6577_AUXADC = "y";
|
|
# MEDIATEK_WATCHDOG = "y";
|
|
NET_MEDIATEK_SOC = "y";
|
|
NET_MEDIATEK_SOC_WED = "y";
|
|
NET_MEDIATEK_STAR_EMAC = "y"; # this enables REGMAP_MMIO
|
|
NET_VENDOR_MEDIATEK = "y";
|
|
PCIE_MEDIATEK = "y";
|
|
|
|
BLOCK = "y"; # move this to base option
|
|
|
|
SPI_MASTER = "y";
|
|
SPI = "y";
|
|
SPI_MEM="y";
|
|
SPI_MTK_NOR="y";
|
|
SPI_MTK_SNFI = "y";
|
|
|
|
MTD = "y";
|
|
MTD_BLOCK = "y";
|
|
MTD_RAW_NAND = "y";
|
|
MTD_NAND_MTK = "y";
|
|
MTD_NAND_MTK_BMT = "y"; # Bad-block Management Table
|
|
MTD_NAND_ECC_MEDIATEK= "y";
|
|
MTD_NAND_ECC_SW_HAMMING= "y";
|
|
MTD_SPI_NAND= "y";
|
|
MTD_OF_PARTS = "y";
|
|
MTD_NAND_CORE= "y";
|
|
MTD_SPI_NOR= "y";
|
|
MTD_SPLIT_FIRMWARE= "y";
|
|
MTD_SPLIT_FIT_FW= "y";
|
|
|
|
|
|
MMC = "y";
|
|
MMC_BLOCK = "y";
|
|
MMC_CQHCI = "y";
|
|
MMC_MTK = "y";
|
|
|
|
# Distributed Switch Architecture is needed
|
|
# to make the ethernet ports visible
|
|
NET_DSA="y";
|
|
NET_DSA_MT7530="y";
|
|
NET_DSA_TAG_MTK="y";
|
|
|
|
PSTORE = "y";
|
|
PSTORE_RAM = "y";
|
|
PSTORE_CONSOLE = "y";
|
|
PSTORE_DEFLATE_COMPRESS = "n";
|
|
|
|
SERIAL_8250 = "y";
|
|
SERIAL_8250_CONSOLE = "y";
|
|
SERIAL_8250_MT6577="y";
|
|
# SERIAL_8250_NR_UARTS="3";
|
|
# SERIAL_8250_RUNTIME_UARTS="3";
|
|
SERIAL_OF_PLATFORM="y";
|
|
|
|
# Must enble hardware watchdog drivers. Else the device reboots after several seconds
|
|
WATCHDOG = "y";
|
|
MEDIATEK_WATCHDOG = "y";
|
|
};
|
|
};
|
|
boot = {
|
|
commandLine = [ "console=ttyS0,115200" ];
|
|
tftp.loadAddress = lim.parseInt "0x4007ff28";
|
|
imageFormat = "fit";
|
|
};
|
|
filesystem =
|
|
let inherit (pkgs.pseudofile) dir symlink;
|
|
in
|
|
dir {
|
|
lib = dir {
|
|
firmware = dir {
|
|
mediatek = symlink firmware;
|
|
};
|
|
};
|
|
};
|
|
|
|
hardware =
|
|
let
|
|
openwrt = pkgs.openwrt;
|
|
mac80211 = pkgs.mac80211.override {
|
|
drivers = [
|
|
"mt7615e"
|
|
"mt7915e"
|
|
];
|
|
klibBuild = config.system.outputs.kernel.modulesupport;
|
|
};
|
|
in {
|
|
ubi = {
|
|
minIOSize = "2048";
|
|
eraseBlockSize = "126976";
|
|
maxLEBcount = "1024"; # guessing
|
|
};
|
|
|
|
defaultOutput = "ubimage";
|
|
# the kernel expects this to be on a 2MB boundary. U-Boot
|
|
# (I don't know why) has a default of 0x41080000, which isn't.
|
|
# We put it at the 32MB mark so that tftpboot can put its rootfs
|
|
# image and DTB underneath, but maybe this is a terrible waste of
|
|
# RAM unless the kernel is able to reuse it later. Oh well
|
|
loadAddress = lim.parseInt "0x42000000";
|
|
entryPoint = lim.parseInt "0x42000000";
|
|
rootDevice = "ubi0:liminix";
|
|
dts = {
|
|
src = "${openwrt.src}/target/linux/mediatek/dts/mt7622-linksys-e8450-ubi.dts";
|
|
includes = [
|
|
"${openwrt.src}/target/linux/mediatek/dts"
|
|
"${config.system.outputs.kernel.modulesupport}/arch/arm64/boot/dts/mediatek/"
|
|
];
|
|
};
|
|
|
|
# - 0x000000000000-0x000008000000 : "spi-nand0"
|
|
# - 0x000000000000-0x000000080000 : "bl2"
|
|
# - 0x000000080000-0x0000001c0000 : "fip"
|
|
# - 0x0000001c0000-0x0000002c0000 : "factory"
|
|
# - 0x0000002c0000-0x000000300000 : "reserved"
|
|
# - 0x000000300000-0x000008000000 : "ubi"
|
|
|
|
networkInterfaces =
|
|
let
|
|
inherit (config.system.service.network) link;
|
|
inherit (config.system.service) bridge;
|
|
in rec {
|
|
wan = link.build { ifname = "wan"; };
|
|
lan1 = link.build { ifname = "lan1"; };
|
|
lan2 = link.build { ifname = "lan2"; };
|
|
lan3 = link.build { ifname = "lan3"; };
|
|
lan4 = link.build { ifname = "lan4"; };
|
|
lan = lan3;
|
|
|
|
wlan = link.build {
|
|
ifname = "wlan0";
|
|
dependencies = [ mac80211 ];
|
|
};
|
|
wlan5 = link.build {
|
|
ifname = "wlan1";
|
|
dependencies = [ mac80211 ];
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
}
|