Arnout Engelen
|
50ca07fdbe
|
get kernel config from openwrt
Now the kernel starts:
```
Starting kernel ...
Linux version 5.15.137 (nixbld@liminix.builder) (mips-unknown-linux-musl-gcc (GCC) 13.2.0, GNU ld (GNU Binutils) 2.40) #1 SMP Fri Jan 26 14:47:51 UTC 2024
SoC Type: MediaTek MT7621 ver:1 eco:4
printk: bootconsole [early0] enabled
CPU0 revision is: 0001992f (MIPS 1004Kc)
VPE topology {2,2} total 4
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Zone ranges:
Normal [mem 0x0000000000000000-0x0000000007ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x0000000007ffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
OF: fdt: No valid device tree found, continuing without
percpu: Embedded 11 pages/cpu s14544 r8192 d22320 u45056
Built 1 zonelists, mobility grouping on. Total pages: 32512
Kernel command line:
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Writing ErrCtl register=0003003d
Readback ErrCtl register=0003003d
mem auto-init: stack:all(zero), heap alloc:off, heap free:off
Memory: 119864K/131072K available (6564K kernel code, 622K rwdata, 1244K rodata, 1220K init, 217K bss, 11208K reserved, 0K cma-reserved)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
rcu: Hierarchical RCU implementation.
rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
NR_IRQS: 256
Kernel panic - not syncing: Failed to find mediatek,mt7621-sysc node
---[ end Kernel panic - not syncing: Failed to find mediatek,mt7621-sysc node ]---
```
I'm guessing the important bits are:
```
OF: fdt: No valid device tree found, continuing without
Kernel panic - not syncing: Failed to find mediatek,mt7621-sysc node
---[ end Kernel panic - not syncing: Failed to find mediatek,mt7621-sysc node ]---
```
... due to me booting with 'bootm <image>' instead of 'bootm <image> - <dtm>'
because it seems my version of u-boot doesn't support '-' for the ramdisk.
|
2024-01-27 15:59:44 +01:00 |
|
Arnout Engelen
|
4559072cbf
|
Add support for TP-Link Archer AX32
When booting over tftp:
MT7621 # bootm 0x868c3000
## Booting image at 868c3000 ...
Image Name: MIPS Liminix Linux
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2457948 Bytes = 2.3 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
nm_init:791
nm_initFwupPtnStruct:276
nm_lib_readPtnTable:738
[NM_Debug](nm_lib_readPtnTable) 00743: NM_PTN_TABLE_BASE = 0xfe0000
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 1054, requried len = 8192
[NM_Debug](nm_lib_readPtnTable) 00751: Reading Partition Table from NVRAM ... OK
[NM_Debug](nm_lib_readPtnTable) 00759: Parsing Partition Table ... OK
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 3, requried len = 3
[NM_Error](nm_api_checkTestMode) 00417: factory boot check testmode flag is not 1.
### test_mode=disable,boot_args:console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/etc/preinit mtdparts=raspi:256k(uboot),4096k(uImage),11968k@0x440000(rootfs),64k@0xff0000(ART) mem=128M test_mode=disable
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
|
2024-01-27 15:59:43 +01:00 |
|